Aluminum rims black 9x17 ET + 16 with TÜV certificate for Jeep Wrangler JK from year 2007
- suitable for:Jeep Wrangler JK and Jeep Wrangler JK Unlimited from 2007 onwards
- Dimension: 9x17"
- offset: ET + 16
- Bolt circle: 5x127mm
- center hole: 83 mm
- Permitted wheel load: 726 kg
- The original wheel nuts can still be used
- Black powder-coated
- With TÜV expert opinion
The following tire sizes are listed in the report taking into account the respective requirements:
265/70 R 17- 115 *) (U = 2452 mm) 1) , 3), 5), 6), 9)
285/70 R 17- 118 *) (U = 2500 mm) 1), 2), 3), 5 ), 6), 9)
315/70 R 17- 125 *) (U = 2665 mm) 1), 2a), 3), 4), 5), 5a), 6), 8), 9)
33 x 12.50 R 17- 114 *) (U = 2520 mm) 1), 2a), 3), 4), 5), 5a), 6), 8), 9)
35 x 12.50 R 17- 119 *) (U = 2675 mm) 1), 2a), 3), 4), 5), 5a), 6), 7), 8), 9)
Circulation and Information:
1) Only front and rear tires and wheels of one make and one type are allowed. *) ... The required speed index can be found in the vehicle documents. The suitability of the tires used, in particular the required tire inflation pressure in conjunction with the existing load index at the respective maximum speed, the maximum axle loads and camber values u200bu200band when using different tire sizes front and rear also the usability in connection with electronic control systems (ABS , ASR etc.) must be proven by the tire manufacturer. If the tire inflation pressure differs from the standard pressure, the driver of the vehicle must be informed accordingly (air pressure sticker, supplementing the operating instructions).
2) At the front and rear wheelhouses sufficient wheel cover shall be provided by fitting suitable parts or by other appropriate means. Depending on the condition of the vehicle (eg lowered vehicle, wheel cover widening, etc.) it may be possible that the wheel cover is adequate.
2a) At the front and rear wheelhouses, the installation of suitable parts or other suitable measures shall provide sufficient wheel coverage.
3) The circlips on the front and rear wheel bolts need to be removed.
4) By limiting the steering stop, make sure that the stabilizer is sufficiently free. Depending on the tolerance of the vehicle, it may be possible that the clearance is sufficient.
5) Vehicles fitted with the standard 245 / 75R16 tires require a speedometer check and re-adjustment. If a readjustment is made, the series tires can only be used optionally if it can be shown at the same time that the tachometer setting is still correct for these tires as well.
5a) It is a Ü Verification and possibly readjustment of the speedometer required. If a readjustment is made, the series tires can only be used optionally if it can be shown at the same time that the tachometer setting is still in compliance with these tires.
6) The use of snow chains is not allowed.
7) This wheel / tire combination is only allowed in conjunction with a chassis suspension of at least 40 mm.
8) Due to the increased rolling circumference, the wheel load is reduced to the following values: U = 2520 mm - Load capacity of the special wheel: 720 kg U = 2675 mm - Load capacity of the special wheel: 680 kg Accordingly, the permissible To reduce rear axle load in connection with this wheel / tire combination. A reduction of the front axle load is not allowed.
9) The following special wheels are permitted on the front and rear axles: Version: 12758216 / Wheel identification: 1422.25 / Identification Centering ring: Ã~ 82? 71,6mm / bolt circle: 127/5 / center hole: 71,6mm / press-in depth: 16mm / zul wheel load: 726kg / zul. Rolling circumference: 2500mm
Standard or accessory wheel nuts with 60 degree cone angle are used. Tightening torque: 120 Nm
(These are not included)
4K142