Aluminum rim polished 9x17 ET + 16 with TÜV certificate for Jeep Wrangler JK from year of construction 2007
Fits:
- Jeep Wrangler JK Bj. from 07
- Jeep Wrangler JK Unlimited
- Dimension: 9x17
- offset: ET + 16
- Bolt circle: 127 mm
- number of holes: 5
- center hole: 83 mm
- Permitted wheel load: 726 kg
- Wheel nuts are not included
- polished
- With TÜV expert opinion
The following tire sizes are listed in the report taking into account the respective requirements:
265/70 R 17- 115 * ) (U = 2452 mm) 1), 3), 5), 6), 9)
285/70 R 17- 118 *) (U = 2500 mm) 1), 2), 3), 5), 6), 9)
315/70 R 17- 125 *) (U = 2665 mm) 1), 2a), 3), 4), 5), 5a), 6), 8), 9)
33 x 12.50 R 17- 114 *) (U = 2520 mm) 1), 2a), 3), 4), 5), 5a), 6), 8) , 9)
35 x 12,50 R 17- 119 *) (U = 2675 mm) 1), 2a), 3) , 4), 5), 5a), 6), 7), 8), 9)
Editions and Hints:
1) Only front and rear tires and wheels of a manufacturer and type are allowed. *) ... The required speed index can be found in the vehicle documents. The suitability of the tires used, in particular the required tire inflation pressure in conjunction with the existing load index at the respective maximum speed, the maximum axle loads and camber values u200bu200band when using different tire sizes front and rear also the usability in connection with electronic control systems (ABS , ASR etc.) must be proven by the tire manufacturer. If the tire inflation pressure deviates from the standard pressure, the driver must be advised of this in a suitable manner (air pressure sticker, supplementing the operating instructions).
2) The front and rear wheel houses are replaced by the attachment appropriate parts or other suitable measures to produce sufficient wheel cover. Depending on the condition of the vehicle (eg lowered vehicle, wheel cover widening, etc.) it may be possible that the wheel cover is sufficient.
2a) At the front and rear wheel houses is due to the 3) The circlips on the front and rear wheel bolts must be removed.
4) By limiting the steering stop is sufficient Freedom to produce stabilizer. Depending on the tolerance of the vehicle, it may be possible that the clearance is sufficient.
5) For vehicles with the standard tire size 245 / 75R16 is a check and possibly Re-adjustment of the speedometer required. If a readjustment is made, the series tires can only be used optionally if it can be shown at the same time that the tachometer setting is still correct for these tires as well.
5a) It is a Ü Verification and possibly readjustment of the speedometer required. If a readjustment is made, the series tires can only be used optionally if it can be shown at the same time that the tachometer setting is still correct for these tires as well.
6) The use of snow chains is not allowed.
7) This wheel-tire combination is only allowed in conjunction with a chassis extension of at least 40 mm of the ASP Eberle.
8) Because of the enlarged If the rolling circumference is reduced, the wheel load is reduced to the following values: U = 2520 mm - Load capacity of the special wheel: 720 kg U = 2675 mm - Load capacity of the special wheel: 680 kg Accordingly, the permissible rear axle load in connection with this wheel Reduce tire combination. A reduction of the front axle load is not permitted.
9) The following special wheels are permissible on the front and rear axles:
version: 12758216 marking wheel: 1422.25
Standard or accessory wheel nuts with 60 degree cone angle are used. Tightening torque: 120 Nm
(These are not included)
Acceptance of attachment:
After the technical change has been made, the vehicle is immediately an officially recognized expert or examiner of a technical inspection body or a test engineer of an officially recognized monitoring organization on presentation of this partial report.
4K749